Jumbo Curtainsider Semi-Trailer

Fliegl 3-Achs Jumbo Gardinen Sattelauflieger

3 vehicles in production
Please note: the images are archive photos. The vehicle may be in use.
#Chassis – Semi-Trailer for Haulage
- Fine-grain steel welded construction, fifth wheel plate with replaceable 2" kingpin
- Outer frame with "Load Lock" profile for lashing straps
- 13 additional pairs of lashing rings recessed into outer frame, 5 t each
- 24 t 2-speed landing legs, single-side operation, half-round foot, straight mounting plate, sliding foot compensation, min. swivel clearance 2,220 mm
- "Heavy Blocker 2.0" rear cross impact protection
Crsdpfez Ahxdjx Aagsi
- Heavy-duty pallet stop, bolted both sides, ca. 15–20 mm high, lashing points ca. every 380 mm
- Lifting table to gooseneck, ca. 3,000 mm long, hydraulically raised for driving onto gooseneck
- Hydraulic lifting table with own electric power pack, in aluminium box with stainless steel door, right side (direction of travel)
- 2 x 12V batteries with bracket and battery box, charging cable front to rear, 7-pin charging socket at front
#Axles & Suspension
- Laser-measured axles/chassis, reducing tyre wear and fuel consumption
- Rear axle self-steering, automatic reverse lock via reversing light, additional manual lock switch on vehicle
- Air suspension with raise & lower valve plus auto-reset function
- Max. rear ramp/loading height with air suspension lowered ca. 1,050 mm
#Wheels & Tyres
- 235/75 R 17.5", steel wheels in twin arrangement
#Braking System
- 2-line compressed air braking system
- Spring-loaded parking brake
- Vehicle stability system
- Trailer info centre, displays data such as axle load and mileage
- Axle load detection via EBS CAN-bus signal, shown on cab display
- 2 mismatch-proof coupling heads at front
- EBS electronic braking system with EBS socket at front
- Tyre pressure monitoring system (TPMS) per ECE R 141, shown on tractor display via EBS
#Electrics
- 24V, LED multi-chamber lights, flashing side lights
- 2 white LED position lights at front
- 2 white/red LED outline marker lights at rear
- 2 additional LED work lights at rear
- LED work lights on both sides
- 2 x 7-pin and 1 x 15-pin mismatch-proof sockets at front
#Front Wall / Front Corner Posts
- Front wall lined internally to ca. 2,500 mm height, ca. 30 mm thick plywood panel
#Centre Posts
- 3 pairs of sliding posts, adjustable along full length, 4 insertion pockets, long pocket at bottom
- 3 pairs of post positions
#Slats
- 5 rows of wooden slats
- 4 pairs of variable steel slats, combined with variable beams for front/rear load securing; slats omitted where steel slats fitted, at rear in the well
- 4 variable beams, only combined with variable steel slats, for front/rear load securing
#Roof
- Fliegl-Blitz-Verdeck
- Sliding roof, rear end-lift folds up, roof slides rear to front, L-shaped roof rail for automotive industry, internal width between roof rails ca. 2,490 mm
- EcoLift – roof lifting mechanism, raised ca. 380 mm, both sides, gas strut support
#Registration Country / Plates
- With DEKRA inspection and certificate (per §13 EC-FGV)
- Fliegl manufacturer's certificate for body strength per EN 12642 XL
- Fliegl manufacturer's certificate for body strength per DL 9.5, pallet stop both sides, ca. 20 mm high, loading height reduced by ca. 20 mm
- Warning panel per ECE-70